seal hub

Moreover, it is advisable to replace any hoses that show signs of aging or damage. Most manufacturers recommend routine checks to ensure that hoses remain in optimal condition and to replace them every few years, even if no visible issues are detected.

3. ถอดท่อยางเบรกเก่า โดยปกติแล้ว ท่อยางเบรกจะเชื่อมต่อกับคาลิปเปอร์และถังน้ำมันเบรก ใช้ประแจในการคลายเกลียวและถอดท่อยางเบรกเก่าออก

Since hose may change in length from +2% to -4% under the surge of high pressure, provide sufficient slack for expansion and contraction.
Never use a bending radius less than the minimum shown in the hose specification tables. The bending radius of the hose should be far away from the hose fitting (A＞1.5R)
Hose bending radius is bigger when it is in motion.
Choose proper fittings, avoid twisting in hose lines bent in two planes.
Avoid twisting in hose by use clamp properly.
Hose should not be twisted, hose is weak when installed in twisted position. Also pressure in twisted hose tends to loosen fitting connections. Design so that machine motion produces bending rather that twisting.
Leave proper length when the hose in connected
Choose proper fittings, avoid too small bending radius and excess force.
Choose proper fittings, avoid excessive hose length.
Reuse friction, avoid hose touching the object directly or far away from the object.
Hose Active Working Pressure Working Life
As shown , when active working pressure in 1.25 times recommended working pressure, the hose working life is only half of i under working in recommended working pressure.
Store Conditions of the Assembly.
1.If possible, the storing temperature range is within 0-30 ℃. During storing, temperature should not exceed 50℃
2.The storing areas can not place equipment within can produce ozone.For example mercury vapour lamp, high voltage electric device and other equipment which can produce spark or set out electricity.
3.Can not be placed with erosive products or exposed over gas-volatile on these products.
4.Far away from heat source and equipment which can produce electric field or magnetic field
5.Avoid sunshine or strong artificial light source
6.Avoid to touch the sharp objects or the ground
7.Guarantee against rodent attacking.
8.Observe the rule of “First in, then first out”

2. Reinforcement Layer This is a critical part of the hose that provides strength and durability. A 3000 PSI hose often includes multiple layers of high-tensile steel wire braiding or spiraling, which helps it resist bursting under high pressure. The reinforcement can vary depending on the hose's intended application.

Care and Maintenance of Steam Cleaner Hoses

ከመወርወር ወደ ማብረቅ የሚለወጥ መሥራች የሆነ፣ የሃምሌ ቋሚ የመታ ቀረባ መሥሪያ በአርኪስ ማብረቅ ዝርዝር መረጃ እንዲሁም በጣም አስፈላጊ የሆነ ጥያቄ ይወድቃልን። ይህ መሥሪያ በዕውቀት ዘርዝር መረጃ ሙሉ መለኪያዎችን ያካትታል። በተለይ፣ አብዛኛው ስርዓት ወቅት ለማብረቅ ይሳቢያዎችን ይፈልጋሉ።

Өндөр даралтын шлангыг үйлдвэрлэхэд шилдэг технологи, материал хэрэглэх нь зам тээврийн аюулгүй байдал, тоног төхөөрөмжийн үр ашиг, хүний эрүүл мэндийг хамгаалахад чухал үүрэгтэй. Ихэнх шлангууд нь резин, PVC болон бусад синтетик материалаар хийгддэг. Тэдгээрийн давуу тал нь ус, тос, химийн бодис, өндөр температур зэрэгт тэсвэртэй байх явдал юм.